To make a beauty pageant sash, purchase a length of wide ribbon appropriate for the size of the girl wearing the sash. Sew the ribbon on an angle so it curves nicely around the body, and add a trim if desired. Try it on the girl, and sew the bottom seam. Add the name on the sash with glitter, paint or embroidery.
- Purchase a wide ribbon
Choose a wide ribbon that matches the color scheme or the girl’s dress. If desired, purchase a slightly narrower white ribbon to add to the top of the other one to create a layered look. Typically, 2 yards is plenty of ribbon. However, adjust as necessary to fit the body wearing the ribbon.
Purchase trim if desired
If desired, purchase lace or fringe to add to the sash. Purchase the same amount of trim as ribbon. If used, it is sewn on one side of the ribbon.
Fold the ribbon in half
Keeping right sides together, fold the ribbon in half. If your ribbon is 2-yards long, you would then have a doubled piece that is 1-yard long.
Sew the shoulder seam
Measure 1-1/2 inches from the fold and mark with a pin. Take a straight edge and measure from the mark to the opposite corner of the fold. Draw a line along the straight edge. This gives a short diagonal line. Sew over this line. Trim off the extra ribbon. Use a zig-zag stitch on the raw edge to prevent fraying if necessary.
Attach the trim if desired
Unfold the ribbon at the seam. Press if desired. Sew the trim, if used, along the bottom side of the ribbon. If using a second ribbon over the first, add it now as well.
Write on the sash
Write, paint or embroider the name on the sash. If desired, use a template so the letters are even and pretty. Measure in advance to center the letters nicely on the front part of the sash.
Sew the bottom seam at the hip
Put the sash on the girl, and hold it at the hip. Pin the front of the sash over the back. Remove the sash and sew a strong seam. Cut any extra ribbon off the sash, if desired. Again, if fraying is a concern, sew the cut ends of the ribbon with a zig-zag stitch.
A sash belt is an easy way to accessorize a dress. Perhaps your “little black dress” needs to be accessorized for the office Christmas party. You could purchase a silk brocade sash for about $30, or you could make one for less than half the cost. Even your standard summer sheath could be more chic with a contrasting or brightly colored sash made of a polyester/cotton blend. If you have minimal sewing skills, you can make the sash belt you need in less than one hour.
Purchase at least 1/4 yard of fabric to make the sash. A quarter yard of fabric will make a sash up to 4 inches wide and 45 inches long. This would be adequate for someone who has a waist size of 25 inches or less. Purchase a 1/2 yard if your waist is larger. You may have to seam two strips of fabric to make your sash belt long enough. It is always better to have too much fabric than not enough. Buy matching polyester/cotton thread, and a buckle or d-ring if you plan to use one on your sash belt.
Determine the length of your sash belt. Measure your waist and add at least 12 inches to the measurement for use with a belt buckle, and 24 inches if you plan to tie your sash. Decide how wide you want your sash belt to be. Double the width of sash and add 1 inch for seams. For example, if your waist is 30 inches and you want to tie your sash, you will need at least 54 inches of fabric for the length. If your sash will be three inches wide, cut the strip of fabric 7 inches wide. It may be necessary to seam two 7-inch-wide strips of material together to have a length of 54 inches. Most fabric comes in 44- to 45-inch widths, although some is available in 54-inch widths.
Cut fabric to the appropriate width and length as determined in Step 2. Fold fabric lengthwise and, with right sides together, stitch a straight seam 1/2 inch away from the edge of the unfolded side. Turn the sash belt right side out. Press the sash with an iron heated to the appropriate fabric setting. Turn in the raw edges on each end of the sash and hand stitch the unfinished edges together. Use small stitches that are not easily seen.
Follow the package directions for adding a D-ring or buckle to your sash, if directions are included. For a D-ring closure, fold about 2 inches of the sash over the straight sides of the rings. This will create a tab. Hand stitch or machine stitch the tab closed at the base of the tab. Add a straight line of stitching close to the D rings to keep them in place.
If you use a lightweight fabric, it might be necessary to use a fusible interfacing to make the sash a little sturdier. Another fabric option could be a length of wide ribbon (at least two inches in width), backed with fusible interfacing.
Keep fingers close enough to the sewing machine needle to correctly guide the fabric, but far enough away to avoid puncturing your fingers with the needle.
- How to Make a Cafe Curtain
- How to Make Bottom Curtain Tiers
- How to Make Sheer Panel Curtains for a Drawstring Curtain Rod
- How to Make White Sheer Curtains Without Sewing
- How to Measure Windows for Draperies
Sheer or lightweight curtains on sash rods allow light to pass through windows on doors while providing some privacy. Sash rods are slender curtain rods that are used in pairs, one at the top and one at the bottom with the curtain fabric taut between them. Sash rods are secured to the door so the curtains move with the door when it is opened or closed. Curtains are gathered on sash rods with varying degrees of fullness. A curtain that measures double the rod width is typical, but tripling the width creates extra fullness and more privacy.
Measure the window space the curtains need to cover. Add 4 inches to the length of the window space to allow for the header and footer channels for the sash rods. Depending on the weight of the fabric you use, figure double the width of the window space for average fullness. Triple the width measurement if you want very full gathers. Purchase fabric and matching thread, and cut fabric panels according to the measurements.
Turn under the side edges of the curtain panels 1/4 inch, then 3/4 inch more and machine stitch the edges to make the side hems.
Turn under 1/2 inch, then 1-1/2 inches along the upper and lower edges and pin in place. Machine stitch along the 1/2-inch fold edges to make the top and bottom hems. Then stitch 3/4 inch from the upper and lower folded edge, or along the center of the 1-1/2 inch folded hems, to create channels for the sash rods.
Insert the rods through the channel in the hem. The extra hem along the upper and lower edges creates a ruffled header and footer on the curtain to help conceal the rod brackets.
Did you know, the concept of sash window came from Brighton, its architectural splendor is renowned all over the world. It is said that window sashes were evolved with two primary motives, 1 — the maximum influx of light and 2. Maximum space area. So design, restore, and decorate your windows with beautiful sashes and give it a vibrant touch of colors. To make your window sash at home, follow the steps, and create your piece of art.
How to Make a Window Sash
We will firstly need plywood which is four inches larger than the old window sash. With the help of a measuring tape, measure the height and width of the old sash and cut the new sash by adding 4 inches to each dimension of the ply. Step 2.
You are building a square sash, so you’ll need two horizontal and two vertical pieces. Be precise with the measurements of the ply after cutting put it all along and measure the inches again. Even if there are minor gaps, you need to make it again.Step 3.
Once we are ready with the pieces of plywood, lay the cut plywood strips on the template piece in the line. Make sure the template is placed correctly.Step 4.
Most video shows wood glue to be used for fixing the plywood. But if you want your plywood to fix for longtime then use brad nails or screws for the strips. Step 5.
The side two pieces will be of the same size, whereas the top section and the bottom portion will be of different sizes. Two hands are called stiles, the top section is called headrail, and lower is known as a bottom rail. Step 6.
The template keeps the whole sash together and helps to make the perfect window sash. Place the side strips on the templates precisely. Now, place the upper and lower strip on the template and mark the end locations.
The outer panel is done, and now we’ll need a router table. The router table will help us to cut the pieces. Firstly, cut 7/15 inches deep with ⅓ inch straight bit. You can also use stop blocks to cut accurately. Cut ¼ inch groove into the edge of the stiles.
Apply glue towards the faces of stiles and rails. Remove the pieces from the template and adjoin the side pieces. Step 9.
Once we assemble the pieces, clean the glue, and give it time to set. Don’t move it until it’s scorched. It will take an hour to cure the adhesive.
With the help of brad nailer strengthen the joints and fill it with wood putty at the holes.
Cut the sash with sharp ends and proper thickness. The inside frame should get space for the glass to fit in.
Use a glazing compound to the ends of the frame. Lay the glass on top of the glazing compound and give it time to dry. Make sure that the edges of the glass should be firmly rooted in the mixture.
While you add glazing compound, give it space for about 7 inches each so that the glass can be fixed precisely. To smoothen the compound using a puffy knife to make every corner flat and leveled.
We’ll allow the compound and glass for overnight to for the new sash. And now your sash is ready to be painted and used.
This is how you make your window sash. You can also vary the sizes and the inches. Once you are ready with a wooden sash, you can easily paint it. Use acrylic paint on the sash to prevent stains and rust. This way, you can create a very creative window and also play with colors, like every window of the different colored sash. Create your sash and create the magic to your old window.