How to install a water softener

While you may know you need a water softener after testing your water’s hardness, the thought of installing a water softener can be daunting. Whirlpool softeners can be installed by a DIY-er familiar with principles of plumbing.

Water Softener Installation Cost Considerations

If you’re prepared to take on a bit of handiwork, the cost to install a water softener is less than a professional installation. Eliminating the cost of labor means that the price largely depends on the capabilities of your water softening unit, which is measured in grains. Typically, the higher the grain count, the higher the water softener system cost.

The number of people in a household provides a basis for the minimum number of grains you should be looking for in your next unit:

1-4 People:

30,000 grains minimum
5-6 People:

40,000 grains minimum

Another factor that may affect the final price of your DIY water softener project is the ease of installation. If the pre-plumbing for your water softener is conveniently located near the equipment itself, you can save time and money eliminating the need for additional plumbing.

Planning your budget and want to know exactly how much it will be to install your water softener ? Check out our selection of products to find the ideal unit for your needs.

Water Softener DIY Installation

Installing a water softener yourself allows you to work on the project at your own pace and without spending extra money on a plumber. If you’re simply replacing an old water softener, this can be done in under an hour. A new installation does require some additional plumbing knowledge, but can be tackled in a few hours. You’ll want to make sure you have all the necessary supplies and tools before you begin, as you may need to cut some pipes to align your water softener and water supply lines. Creating a detailed checklist before you begin, will ensure you don’t miss any steps.

Whirlpool® Water Softeners come with everything to install and hook up to 1” NPT (National Pipe Thread). ). If your plumbing is smaller or larger than 1”…

Before You Get Started:

  • Two 1” NPT female connectors and enough tubing to connect from the water softener to your existing plumbing. You may have copper, PVC, CPVC, steel or PEX plumbing. Each of these plumbing types may require different materials and different tools for installation.
  • A drain is necessary for the regeneration or recharge process. 12 feet of drain tubing is supplied but if your drain is further then 5 feet away, you will need to purchase enough ½” tubing to reach your drain. The drain should not be more than 30 feet away from the softener and the drain line should not be elevated more than 8 feet above the floor.
  • The power cord (transformer) needs to be plugged into a 110V continuous live outlet. The unit comes with a 10 foot power cord.

Where to Install a Water Softener

If you’re asking yourself, “where does a water softener go?”, it’s time to do a bit of investigating around your home. On the other hand, if you have a general understanding of how to plumb a water softener, you can quickly identify the most effective location.

If you’re installing a whole-home system, you’re going to want to place the softener as close to the entry point for water in your home. As a general rule, it’s best to place a water softener at the earliest possible point in your home plumbing system. That means placing your water softener somewhere it can feed into your water heater, rather than placing it downstream from this equipment. Not only will you prevent hot water from damaging your softener, but you will also extend the life of your water heater by feeding it softer water.

Every installation scenario is different, but some general plumbing requirements for installation include:

  • 3 gallons per minute at the inlet
  • 125 PSI maximum water pressure

Your water softener will need power to function, and general water softener electrical requirements include:

  • A 120V, 60 htz grounded outlet with circuit breaker protection
  • If using an extension cord, ensure that it is a #20AWG appliance replacement cord

Wondering how to install a water softener with a well? As long as the water source enters your home in the same fashion as a municipal water supply, the installation steps are identical.

Typical Basement Installation

How to install a water softener

Typical Slab Foundation Installation

How to install a water softener

Quick Installation Checklist – see installation manual for details

  1. Turn off water supply at main
  2. Drain water lines
  3. Make proper connections (Optional: install remote bypass)
  4. Fill brine tank half-full with salt
  5. Ensure bypass is shut, slowly turn on water, check for leaks
  6. Complete start-up procedure

Related Articles

How to install a water softener

How to install a water softener

How to install a water softener

Extend your warranty
and the life of your softener
with Whirlpool ®
Water Softener Cleanser

Now, you are thinking about how to install a water softener and where to install a water softener? A water softener installation is not tricky, all you need are the right tools and a good step-by-step guide. Although every option comes with a manual that will walk you step by step through the whole process of installing a water softener, you might need the help of a plumber while doing so. However, here are the steps that will ensure the safe and perfect installation of your new water softener.

How to install a water softener

  1. The first step is to stop the flow of water in your house by closing the control valve.
  2. Find the place where you want to install the water softener.
  3. Find the water meter and then cut the pipes precisely from the point where the water enters your house.
  4. At this point, you will have to install the pipe connection. The connection has to be a three-valve. We use a valve to stop water from entering the softener system, stop water from leaving the unit, and thirdly a bypass valve.
  5. The next step is to make sure all connections are tight. If you feel that the links are loose, you can solder it.
  6. Now you need to connect the main tank and the brine tank with a 3/8 standard plastic tube.
  7. By using a hose clamp, you need to join the drain line and the drain elbow.
  8. Next, you have to connect the discharge pipe to the water waste drain.
  9. Finally, connect the main pipe from the unit to the pipeline that goes inside the house.

And Viola! You have successfully installed the new water softener system.

Where to install the water softener?

How to install a water softenerThe type of system that you simply install goes to dictate in massive half wherever you finish up golf shot it. So, if you’re unsure regarding this a part of the duty then I’d recommend hiring a professional plumber for installing your water softener instead of making an attempt to accomplish the task on your own. However, I’d rather have somebody have it away on my behalf than have to the trouble to do it on my very own and risk doing it wrong.

Whole house water softener systems, for instance, need to be installed near the main water pipeline. Do not install your softening unit downstream from your water heater, because the high temperatures may cause a problem to the water softener system. If you’re putting in reverse osmosis or salt-based water softener system, you may additionally make sure that your system is close to a drain, or that it may be flushed into a close-by drain or into a suction pump to be flushed outdoors. Under the sink, models can usually drain straight into the waste line.

How to install a water softener

Smith started as a journeyman plumber and then eventually became a master plumber and has continued to work in the plumbing industry learning all phases of plumbing from new construction to simple plumbing repairs.

How to install a Water Softener – US Water Systems

    cheezbot liked this

More you might like

How Salt-Free Water Softener Systems Are Eco-Friendly

For an eco-minded homeowner, you may find yourself feeling a bit concerned about with a traditional salt-based water softener in your home. After all, there are several possibilities problems associated with traditional water softeners that can leave a harmful impact on the environment. Therefore , if you are looking for a more environmentally safe method, you might want to consider installing a salt-free water conditioner in your own home. To that end, here is a look at how salt-free water systems will be eco-friendly.

Reason #1: Eliminate Discharge

Traditional water softeners typically discharge up to four gallons of salty h2o for every gallon of water that is treated. Not only performs this result in wastewater issues, but many cities are actually banning the employment of salt in water conditioners due to their harmful effects for septic tanks, sewer systems and water treatment models.

Reason #2: Keep Salt Out of Your Water

While the sodium in traditional water conditioners is not supposed to get in the tank, the reality is that it does. In fact , experts estimate that related to 8 mg of sodium is released into normal water for every grain of hardness that is removed. Not only might this salt kill lawns, gardens and houseplants, but it surely can be bad for your health as well. It can also cause a problem with certain home equipment, such as steam irons and evaporative coolers, which are never supposed to be supplied with softened water. When you use a citrus-based procedure on the other hand, non-e of these problems are an issue.

Reason #3: Under no circumstances Replace Your Water Softener System Again

Due to the innovative electronics and many moveable parts found in traditional water softeners, on average, they only last about 10 years. After this period of time, you will find yourself needing to replace the system and disposing of outdated system. Disposal of these old systems only leads to even more environmental waste, while the process of building new water softeners to replace those that have broken down only further leads to pollution your planet. Saltless water softener systems have no electronics or simply moving parts and the softeners are usually backed by a lifetime service contract.

Reason #4: Stop Wasting Salt

Traditional water hair conditioners need to have their brine tanks filled on a regular basis. In fact , most householders find that they need to pour a whole bag of salt on the tank each month. This is certainly a waste of salt that might potentially be used for other purposes. Furthermore, this replacement deserving of can cost anywhere from $4 – $40 per month to replace. The exact cartridges used with salt-free water softeners, on the other hand, generally has to be replaced only every 3-6 months depending on the size of the exact cartridge and the level of water usage. more info

Reason #5: Always keep Beneficial Minerals Where They Belong

One of the unfortunate adverse reactions of using a traditional softener is that it takes out the healthier minerals along with the bad ones. Citrus-based softeners, on the other hand, relax the water without removing the minerals that are beneficial to yourself.

Margie Krueger wanted to protect her home’s plumbing plus decided to invest in the nuvoH2O Saltless Water Softener. She beloved the results so much, she decided to write about it. Her saltless water softener now removes hard-water buildup that filled and corroded her water heater and appliances.

Understanding Water Softener Systems for a Good Purchase

Quality water softener systems can benefit the consumer but many consumers may very well be led astray with poor quality systems of water softener or made to pay a higher price for their softener system. As a result, the wise consumer would do well to check the features bought at any good deal on a water softener.

The person who intends to purchase a water purifier should find out what a softener system is and how it works first. The knowledge would allow the consumer to identify the features available in their preferred softener product to enjoy potable water.

A softener system is used to progression the hard water that is laden with minerals to produce fluffy and clean water that is suitable for consumption. Water softeners producing soft water help in preventing stained dishes and even appliances as well as scaling on pipes.

Water heaters would not endure being clogged with soft water. The softening equipment undergoes an ion exchange process to remove dissolved mineral in the input of hard water. These minerals can include iron, calcium, sulfur and magnesium which are bad for the.

A quality water softener would have a good matrix for small plastic beads known as zeolite. Sodium ions spurt in the zeolite where the water input is pushed passed entangling the undesirable minerals. The sodium ions are copied into the water to make the water softer.

When the amount of sodium is too little, regeneration is required on the zeolite; the common salt is the primary component in soft water regeneration. A deep concentration of brine is passed through the system to reestablish the zeolite; excess brine and mineral residue are actually flushed away.

Alternatively, potassium chloride is used in regeneration for those who are on a low sodium diet. This is also preferred by just those who want to limit their sodium intake. A good standard water purifier would allow a choice of mineral regeneration to benefit the consumer. Other brands use charcoal filters to eliminate undesirable minerals from the source of hard water although this component is more high dollar.

Water softener systems can perform quite well over a warranted period by the manufacturer. Some softener systems allow an automated regeneration which enhances their performance to the convenience of the very consumers; only salt is needed to be refilled. Hence, to lower the number for a manual regeneration which can be inconvenient to consumers.

A water softener removes minerals from water, making a home’s water kinder to bodies, hair, appliances, pipes, and more.

Hard water—that is, water with lots of minerals— is more than a nuisance. It can stain sinks, reduce the cleaning power of detergent, cause buildup in faucets and pipes, and shorten the life of a water heater.

A water softener is the appliance that removes minerals from water. For more about water softeners and how they work, please see the Water Softeners Buying Guide. Here we’ll look at where and how to install one.

How to install a water softener

To find out whether your water is hard, you can buy a water test kit online. This will give you a clear idea of the amounts of minerals in your water. Mailorder Water Test Kit WaterSafe

Though several types of salt-free water softeners are available, a salt-based (ion exchange) softener is the most popular. (Please see the Water Softeners Buying Guide for more information on hard water and choosing a water softener.)

Installation must adhere to local plumbing codes.

Though most homeowners choose to buy and maintain their own water softener, a viable option is to rent one. Over the long run, renting will cost more than buying, but it costs much less up front and can save you the trouble of installing, maintaining, and repairing a system.

Where to Install a Water Softener

If your home has an older water softener that you wish to replace with a new one, plan to put the new unit in the same location. If there is no existing water softener in your home, consider the following advice for locating your new softener.

General location. For starters, a new water softener should be located out of the way but where it is easy to tie it into the plumbing system—in most cases, this is in a basement, garage, or utility room, often near the water heater. Allow enough space around the equipment for easy servicing.

Do not put the softener in an area where freezing might occur; this can cause permanent damage and void your warranty. If temperatures are expected to drop below 40 degrees F (4 degrees C), protect the equipment by relieving the pressure and draining the system. Also avoid direct sunlight—and don’t put the equipment outdoors.

Required hookups. A water softener will need a drain such as a floor drain or utility sink. In addition, the water softener will need a nearby electrical receptacle (not controlled by a switch) that can handle the needed amperage (check the manufacturer’s specifications).

How to install a water softener

A water softener is usually installed near the water heater. City_Wide / Photobucket

How to install a water softener

Where to connect to pipes. For softening a home’s entire water supply, install the softener before the water heater—this helps reduce sediment buildup in the water heater, too. In households where sodium in the drinking water may cause a health risk, it may be necessary to bypass certain faucets used for drinking water (such as the kitchen sink) or, in some cases, soften only the hot water side of the water supply system. Be aware that your entire cold water system will lose all of the benefits of water softening if you do this. Here a water softener is connected where it can bypass the home’s drinking water supply. ©Photographee.eu / Shutterstock.com

Another option is to opt for a salt-free water softening system (see Salt Free Water Softeners). Don’t place the softener after (downstream from) the water heater—temperatures above 110 degrees F (43 degrees C) may damage the softener and void the warranty.

Plumbing a Water Softener

Most water softeners come with a bypass valve that you must assemble and attach to the unit. In addition, some local plumbing codes require that you install shutoff valves to the pipes that lead to and from this valve so the water to and from the softener can be turned off easily. If your softener has such a bypass valve, attach it to the softener, following manufacturer’s instructions.

1 Clear and sweep the area. Position the water softener where it belongs so you can easily measure for the connecting pipes. Pay attention to orientation of the unit—the INLET should be attached to the water supply pipe and the OUTLET should go toward the water heater.

2 Shut off the house water supply valves. (For more about shutting off the water supply, see How to Shut Off the Water Supply.) Turn off the water heater’s water supply and the power to the water heater (the circuit breaker for an electric water heater or the gas valve for a gas water heater). Then open a couple of bottom-floor faucets or hose bibbs to drain the water from the pipes.

3 Cut into the water supply line, using a pipe cutter, and install elbow fittings so you can run two lines to the inlet and the outlet ports of the bypass valve. Again, pay attention to orientation: Hard water from the water supply will run into the softener’s inlet, and soft water will run out to supply the house’s fixtures and faucets. If you want an outlet, such as a hose bibb, to carry hard water, install a T fitting prior to the softener and run it to the outlet.

4 Cut and install the pipes that lead to the bypass valve. Solder all the fittings and nipples before attaching them to the plastic bypass valve (the heat from soldering could damage the plastic). For more, see How to Cut & Solder Copper Pipes. If the pipes are too large, use a reducing fitting to install pipes of the correct size. Use the compression fittings supplied with the softener to attach the pipes to the unit. Note: If you home’s electrical system relies upon the plumbing for safe grounding, you must install a jumper across the water softener installation piping to ensure proper grounding.

5 Clamp the drain hose to the softener, and run it to a drain or utility sink. The end of the hose must be at least 2 inches above a drain hole to prevent back siphoning of waste water, and it should be securely clamped.

Note that the drain hose must be sized according to the distance of its run and its height in relation to the inlet. Typically, a 1/2-inch interior diameter (ID) line can run up to 15 feet if its discharge is lower than the inlet. You’ll need 5/8-inch ID for the same distance if the discharge is slightly higher than the inlet. For a distance of 15 to 25 feet and/or if the drain is above the inlet, opt for 3/4-inch ID. The drain line should not be positioned more than 10 feet above the floor.

Hard water is highly common in the U.S., present in over 70% of American households. Hard water contains a high concentration of dissolved minerals such as magnesium and calcium.

How to install a water softenerThese dissolved minerals have been known to cause stains, clog pipes, and damage to appliances as the mineral deposits build up in them. They also alter the taste of the water, making it hard to drink or cook with.

However, water softeners have emerged as a solution to hard water problems. The state health department recommends that people with water containing minerals exceeding seven grains per gallon use a water softener.

If tests on the water you use show that you need a water softener, we’ve created a detailed guide to help you understand how you can install one for home use. Click here to see more details.

How to Install a Water Softener

Step One: Fix the Bypass Valve and Attach the Water Supply

The purpose of a bypass valve is to provide alternative access to water when your water softener is not functional. Some companies provide a shutoff valve for this purpose. A bypass valve is helpful during periods of maintenance and repair of the appliance.

After installing a bypass valve, you should then pipe it into the water supply. Experts recommend you use flexible pipes instead of rigid ones because they are easy to remove if you decide to take out your water softener.

Before connecting the water softener to a water inlet, you must shut off the water supply first to avoid it coming in contact with the electrical components. Connect the flexible pipes to the water supply first, then to the water inlet valve on the water softener.

Step Two: Connect the Tubes and Drain Pipes

If your appliance comes with separate water and mineral deposit tank, you should connect the tubing between the two to ensure the continuous flow of water through the system. It would help to secure these pipes using a hose clamp to avoid unnecessary movement that might damage them.

After connecting the two tanks, you should then proceed to install a drainage pipe. Most water softeners come with two drainage pipes. One is connected to the mineral deposit tank to control the overflow. The other is connected to the control valve of the water backflow.

It is advisable to connect both pipes to the main drainage channel in the house to avoid costly drainage installations.

Step Three: Test Run Your Water Softener

Once you have made and secured all the connections, plug your system into a power supply to give it a test run. The test run will help you identify any leaks or abnormalities in the system before they become a significant problem.

Open the water shutoff valve and confirm that water is flowing freely through the water softener.

If this test was a success, next, follow the manufacturer’s instructions to perform a backwash cycle. A backwash cycle will get rid of any air bubbles that might interrupt the continuous flow of water in the water softener. It will also loosen the resin beads used to trap the mineral deposits, thereby preventing any clogging.

In Need of a Water Softener? Herriman, Utah, Has Plenty Available

Apart from safeguarding your home appliances, a water softener will also help you avoid staining your teeth and clothes, among many other dangers posed by hard water. Be sure to use a reputable dealer with an applicable warranty if you encounter any problems after your purchase.

Get a water softener in Herriman, Utah, today and enjoy the benefits of clean and safe water in your house.

Adding a Pre-Filter Protects and Improves the Effectiveness of your Water Softener

How to install a water softener

Plumbed water softener in basement.

Okay, so you’ve decided to install a sediment filter with your water softener, but you’re wondering if you should install the water filter before or after the softener.

A sediment filter should always go before your water softener. A water softener is not made to remove silt and dirt, that’s what a sediment filter is made for. A sediment filter installed before the softener will protect and prolong the life of your water softener.

What’s in Your Water?

You’ve probably heard it before, but the best way to know what is in your water and how to deal with it, is to have your water tested.

This is the only way to know for sure, what’s in your water and how to treat it.

Most people are reluctant to test their water, because it costs money and takes effort to send it to a lab. I get it, I tend to be frugal this way.

One simple and free approach you can do is to fill up a large clean, white container from your cold water and see if you can notice any discoloration or particles in the water. A white 5-gallon pail is perfect for this home test, or even your bathtub.

A large body of water is easier to spot murkiness or discoloration in water. You’ll also want to look for any particulates floating, or settling to the bottom.

Install a Sediment Filter, Just in Case

How to install a water softener

A fouled sediment filter.

At this point, you may want to install a filter, even if it’s just to capture a small amount of sediment. For those of us on well water, having a sediment pre-filter is a must.

A water supply from a municipal source is less likely to have sediment and particulates in it, but it’s still not uncommon.

Maybe you already know that you want to install a sediment filter. You’ve seen particulates in your water, or maybe you’ve noticed traces of sediment in your toilets. In that case, I would suggest installing a Point of Entry sediment filter, after your Holding Tank (if on on well), but just before your water softener.

Dirt, silt, sand, and other types of sediment will make your water softener less effective and shorten the life of the softeners resin beads. Removing these contaminants will protect your softener.

If you can find one, I suggest installing a clear filter-housing, so that you can visibly see the condition of the filter without having to close the valves and remove the housing for inspection. With a glance, I can quickly see the condition of my filter to see if it needs changing.

A dirty filter will have a thick coat of medium-brown colored sludge, as shown in the image above. As the sediment on the filter grows thicker with use, water pressure in the house gradually drops and is very noticeable.

Varying Levels of Contamination

How to install a water softener

Dirty sediment water.

At certain times, my well water can run fairly clean, where I don’t have to change my sediment filter for weeks. Other times, during periods of prolonged rains, or during prolonged dry weather, my sediment filter seems to become clogged much more quickly and I have to change it out about once a week to restore our water pressure.

At my place, when I turn on a faucet and find it’s flowing slower than normal, or if the pressure drops a lot when more than one person is running water in different parts of the house, I also know it’s time to change out my sediment filter.

The Water Softener is Also a Filter

The water softener itself is a filter. A water softener is meant to filter out calcium and magnesium minerals, not particulates and dirt. If dirty water is allowed to flow into the water softener, dirt can collect on the rotating valves in the controller and become inoperable. This is another good reason to install a sediment filter before the softener.

Water softeners will remove small amounts of iron, but are not specifically designed to treat high concentrations. There are more effective ways to deal with high iron levels. We’ll discuss this in another post.

Post Softener Filtration

Adding a carbon filter, placed after the softener will remove any chemical contaminants that may be present in the water, such as chlorine, and agricultural pesticides and herbicides.

Conclusion:

A pre-filter is not necessarily needed for all water softener installations, but if your water comes from your own private well, installing a sediment filter is usually a necessity.

A whole-house filter housing with sediment filter can be low cost. A good one can be as little as $60. Replacement filters are also reasonably priced. If you have only a few particulates in your supply water, then it could be many weeks before you need to change out your filter.

This will assure that you’re protecting, not only your water softener to keep it working its best, but also protect your other water-using appliances (dish washer, hot water heater, clothes washer, reverse osmosis drinking water filter, etc.

So, it boils down to how clean your incoming water is. Having a pre-filter before your water softener is a smart idea. It will extend the time between softener regenerations. You will prolong the life of your softeners resin bed, by pre-filtering the water with a Sediment filter.

These Crystal Quest Water Softeners come with both a sediment pre-filter, which protects the water softener, and a carbon block post-filter to remove chemicals, tastes and odors that may be present, for a well-rounded water treatment system.

In this article, we’re going to explain how you can upgrade your water at home with a water softener system . Easy and straightforward to install, a water softener system will help reduce the levels of magnesium and calcium in your water, giving you better looking, tasting and smelling water. At Filter Smart, we specialise in helping families in the US enjoy a higher quality of water with our smart, sustainable and easy to install water softener systems . So, if you’re thinking of installing a water softener at your apartment, condo or home, read on!

Why Do I Need AWater Softener System?

Unfortunately across the US, water quality differs between state and even city, and you might start to notice that the water in your kitchen and bathroom is causing limescale build-up, spots on your faucets and isn’t quite cleaning your clothes the way you’d like. Hard water can be quite problematic, as high concentrations of naturally occurring minerals make it difficult for soaps and detergents to lather, not to mention the bad taste and smell that can come from hard water. To change hard water to soft, you’ll need a water softener system . This investment can give you soft water at home for around 10 to 20 years or even longer depending on the model of water softener system you buy.

How Much Space Will AWater Softener Tank Take?

Again this really depends on the type of water softener system you purchase. A standard salt-based water softener will usually need an area of around 3ft by 1.5ft and 6ft in height. However, additional room may also be required to store salt bags to top up the system and ensure it’s working well. These days many American families simply don’t have enough room to install a typical salt-based water softener system in their homes, especially if they live in a small city apartment. Should you be low on space, you can choose a more sustainable model, that doesn’t rely on salt to effectively filter the water within your home. At Filter Smart , we offer activated carbon-based water softener systems that can be easily installed in a property and only requires a small amount of space. Our 1-3 bathroom 12 GPM systems use a small 9 x 48-inch tank and are approximately 52 inches in height, including the valve head. If you require a larger system, our water softener systems still will only be 58 inches tall. As our products don’t use salt, there is no need to store heavy and bulky bags of salt within your home either.

Will It Be Installed Inside or Outside My Home?

Most water softener systems can actually be installed outside your home, however, exposure to wind, rain and sun can have a negative effect on the lifespan of the system. It’s better, if you have the space within your property, to have a water softener system installed inside, to shield it from the elements and increase its lifespan. Although, at Filter Smart, our water softener systems come with a lifetime warranty on tanks and valves. When it comes to installing a water softener system , the ideal placement would be as close to the entry point for water in your home. This will make sure that any water flowing through your property will be professionally filtered and free from any nasties.

How to install a water softener

How to Install A Water Softener From Filter Smart?

When you purchase a sustainable salt-free water filter from us, you’ll be sent a pre-loaded water softener system. The sediment pre-filter and housing units will be sent in separate packages, so don’t worry if you receive one item before the other.

To install your water softener system , all you need is a basic understanding of plumbing and know where the water line is located within your home. This might be inside a garage, or in some cases outside your property. Since our products require no electricity, drain connection or bypasses, installation is pretty straightforward and most people can do this without any assistance. However, please do contact us if you are struggling as we can guide you on how to properly install your new sustainable activated carbon water softener system. All you need to do once you receive your water softener system is to reroute the main line through the system and back out the main water line. Secure and you’re good to go! Now you can start enjoying soft water in your kitchen, bathroom and throughout your home. There is no additional maintenance required, unlike salt-based water softeners, and all you’ll need to do is change the sediment pre-filter annually which can be done in less than a minute.

Global water pollution is prevailing everywhere because of which installing a water softener is a necessity nowadays to improve the quality of water to carry out different applications. However, the real game is how to install a water softener; installing by yourselves might be daunting; finding any expert would cost much money, which becomes non-affordable. People have already spent much on the best water softeners, but if you get a step-by-step guide of installing a water softener, then it’s just like eating a pie. Let’s dive!

How to install a water softener

Salt-based water softener: How to install a water softener?

These are quite common among people, so we’re primarily going to discuss installing a salt-based water softener, before doing so kept all the codes of application of your area in your mind.

Gather tools for Installation

Following tools are necessary for installing a salt-based water softener:

  • Gate valves
  • Measuring tape
  • Pipe cutter
  • Pipe wrench
  • Tee valves
  • 2 compression fittings
  • Teflon tape
  • 2 union fittings
  • Torch and solder

Gather materials for Installation

For appropriate Installation, you should have the following material:

  • PVC solvent
  • Flexible tubing
  • Flux material (replacement of PVC solvent if unavailable)
  • Simple tubing

Installing a salt-based water softener: Step-by-step guide

1. Shutdown mainlines

When you will shutdown the mainlines of water, open the bottom floor faucets, and drain out the other pipelines.

2. Shutdown water heater

To avoid any electric shock, shut down the water heater & main power supply (if you have installed) that runs with electricity or the gas hose.

3. Locate main water line

After this, locate the area in the mainline where you want to install a water softener, keep it closer to the main one for a faster flow rate.

4. Clean area

Sweep the area where you are going to place the water softeners, make sure the Inlet is attached to the pipeline and Outlet to the water heater (If you have).

5. Using pipe cutter

Now, with pipe cutter cut the area on mainline where a water softener is going to install, keep the bucket below because water may drain out when you will cut. Pay special attention to the orientation setting of Inlet and Outlet!

6. Install elbow fitting

Elbow fitting installation is essential at the mainline for the availability of the bypass valve.

7. Measure & attach pipes

Cut the large pipes after measuring up to the bypass valve using a reduce fitting for the correct size and then use compression fitting to connect them.

8. Clamp the hose

To avoid any water drainage, clamp the hose to the water softener very tightly and run it to drain to check, make sure it should be 2 inches above the utility sink.

9. Connect overflow tube

As per the user manual instructions with the water softener, follow them to adjust the height and connect the brine tank with the overflow tube.

10. Plugging

At last, make it start working by plugging into the unit. Open the valve slowly, release water in the unit first, and then to pipes. Partially open the Inlet to escape the air bubbles inside, once the water flows steadily and then move with adequate flow and fill the tank.

Magnetic water softener: How to install a water softener?

The second most commonly used one, which is much easy to install and require fewer things, have a look!

Gather tools

Following tools are necessary for installing a magnetic water softener:

  • Wrench
  • Screwdriver

Installing a magnetic water softener: a step-by-step guide

1. Locate area

These water softeners are compact in size and are easily fixable in any field.

2. Uncover softener

Take the softener out of the box with the user manual and read the provided steps and instructions carefully.

3. Pick tools

Now, fit the magnetic softener on the located area of Installation with the screwdriver and wrench.

4. Plugging

Plug the box with the electric supply so that softener can be easily installed on the pipeline.

Installing a water softener is not as much difficult as it seems to be, just follow up with an informative guides of how to install a water softener and you are quickly done with it. For salt-free water softeners installation and reverse osmosis system, it’s better to hire any technician, due to their difficulty level. We hope that you have found this article pretty good in installing the water softeners, for more information related to water quality testing kits and best water softeners visit us.

How to install a water softener

About James Smith

A writer and blogger with integrated knowledge and background in water softeners and purification process. With the in-depth research on the topic and facts, hands on Knowledge about water softeners and company. Every piece of writing is pure perfection that anybody looks for!