How to paint veneer

How to paint veneer

Applying a couple of coats of paint over a veneer finish can give an item a fresh, new look. The key to a successful paint job, however, is all in the preparation. If you don’t prepare veneer surfaces properly, the paint won’t stick as it should, or it will peel off later. Fortunately, the preparation is easy and just requires a little sanding and a couple of coats of primer.

Pick up supplies like wood glue, cleaning cloths and sandpaper on Amazon

Step 1 – Repair Damaged Areas

Veneer, which is a thin layer of decorative wood, can crack, chip or pull away from the item you want to paint. Repair such problems to ensure that the paint will adhere properly. If part of the veneer has begun to pull away from the underlying surface, use wood glue to set it back in place. If the veneer is missing sections or has become cracked, carefully remove the damaged section and glue a replacement piece of veneer in its place. Wait until the wood glue has dried completely before moving on to the next step.

Step 2 – Clean the Veneer Surface

Dirt, dust, and grime can cling to a veneer surface and interfere with your efforts to give it a new look. Clean the surface of the item you’re planning to paint with a solution of mild dishwashing liquid and warm water. It’s best to avoid soaking the item, however, as the underlying construction may be damaged by too much. Instead, wet a clean cloth with the cleaning solution, wring it out and then wipe the surface to remove any built-up grease and dirt. Rinse the surface and let it dry completely when you’re done.

Step 3 – Sand the Veneer

Use 220-grit sandpaper to sand the veneer finish, being careful to use only light pressure. Avoid sanding it so hard that you move through the veneer to the underlying construction. Use a tack cloth to remove dust particles periodically. After sanding, use a handheld vacuum or your tack cloth to clean up any dust particles that have settled around your work area. If you allow them to remain there, they may blow onto your work as you paint, ruining the look of your paint job.

Step 4 – Apply a Primer

Paint a coat of primer onto the veneer finish, sanding the surface once more after the coat of primer has dried thoroughly. The extra sanding helps to make the surface you’re painting smooth and unblemished. Use your tack cloth to remove dust particles again, and then add another coat of primer. Let the primer dry for about 24 hours.

Step 5 – Paint Over the Veneer

Apply at least two coats of your chosen paint to the veneer surface, painting over the dried primer. If you’re opting for a light color, you’ll need to apply two coats at minimum, and you may need more to achieve the desired effect. If you’ve chosen a dark color, you may need about four coats of paint. Give each coat of paint enough time to dry completely before adding a new coat. Wait 24 to 48 hours before you move on to applying varnish.

Step 6 – Apply Varnish

Apply a few coats of varnish to your painted surface. This is particularly important if you plan to place items on it, work on it, or even handle it frequently. The varnish will help to seal and protect your paint job. Wait 24 hours before you use the freshly varnished surface, making sure it has cured completely.

When you purchase through links on our site, we may earn commissions at no cost to you.

Veneer is a decorative wood layer that’s overlaid on a different surface. Veneer can be primed, painted , stained, and treated just like any other wood surface. The trick to painting veneer is to clean, sand, and prime it before applying a finish coat of paint .

How can I paint over veneer without sanding?

Here are 5 Ways To Paint Furniture Without Sanding : USE A MINERAL PAINT . Mineral paint is very similar to chalk style paints in that no prep or prime is required. USE MILK PAINT + BONDING AGENT. As I already mentioned, the antique desk in this post was not prep- sanded . USE A BONDING PRIMER. USE A LIQUID SANDER /DEGLOSSER.

Can you use furniture polish on wood veneer?

Wood veneer furniture is sensitive to water and can be seriously damaged by condensation. Be sure to thoroughly dry a veneer surface to prevent water damage. To repair small scratches on veneer furniture , simply apply oil polish to the area and massage with a soft microfiber cloth until the scratch fades away.

How can I tell if my furniture is laminate or veneer?

If you see the grain but the pattern tends to repeat and it lacks texture and feels perfectly smooth, it’s probably veneer . If it lacks grain altogether, it’s most likely laminate .

How do you paint over mahogany veneer?

Today, however, you can paint your mahogany veneer dresser with high-performing water-based paint and prep materials that are safe to use indoors. Wash the Surface with TSP. Lightly Sand the Surface with Steel Wool. The Primer Option. Select a Long-Lasting Paint . Consider a More Traditional Paint .

Can you chalk paint over veneer?

I’ve painted veneer before–yes, with chalk paint , and it didn’t work very well. It just scratched right off. Now here is the crucial part which I have never taken stock in before…letting the primer dry for a full 7 days before putting on the real paint .

Can you whitewash veneer furniture?

If you want to create an opaque white finish, the best strategy is to apply a coat of wood primer followed by one or two coats of white paint. If you prefer a pickled look, mix flat latex paint or primer with an equal amount of water.

What happens if you don’t sand before painting?

When You Can Skip Sanding , Deglossing and Priming If the finish on your furniture isn’t damaged or chipping, it’s flat not shiny and you aren’t painting it a drastically different color, then you may be able to just go ahead and start painting . Before painting though, do make sure the piece is clean.

What kind of paint do you use on laminate furniture?

Latex paint is recommended for laminate surface painting projects because of its durability and smooth finish . Try ProClassic Interior Acrylic Latex Enamel for lighter colors, and All Surface Latex Enamel Base for deeper hues.

Can you paint over laminate furniture?

You can sand, prime and paint laminate as if it were a solid wood piece of furniture ! Because it’s often somewhat glossy-looking, and important to sand it down until the finish is very dull before priming. We recommend using 120 grit sandpaper for this. And, unlike real wood , it’s unnecessary to sand with the ‘grain’.

How do you polish veneer furniture?

Aim to dust your wood veneer regularly with a dry, soft cloth to help keep it looking its best. Then for a quick, non-deep clean , you can spray a wood veneer with a light layer of non-ammonia glass cleaner and wipe it with a paper towel. When cleaning , avoid using any furniture polishes that contain wax or silicone.

Which polish is best for veneer furniture?

How do I make my veneer shine?

Restoring a wood veneer tabletop’s shine is accomplished without the need for expensive cleaners. Pour 1/4 cup white vinegar and 3 cups warm water into a plastic spray bottle. Spray the mixture directly onto the veneer tabletop. Allow the veneer tabletop to dry before spraying it with a light coating of glass cleaner.

Painting is one of the easiest (and cheapest) way to change the look of an IKEA furniture. But how do you do it? While the hacker pros among us are quite adept with this basic DIY skill, there are IKEAhacking newbies out there who may need a little guidance, as evidenced by the questions I get on how to paint. IH readers have been very generous in sharing the information and here are previous entries that may be helpful:

As for veneer, the thin decorative wood layer which covers many IKEA items such as the BILLY, EXPEDIT, GALANT, MALM, Bob from Fortune Restoration has volunteered an article on the correct preparation and painting tips for veneer. Follow the steps and you should turn up alright at the end.

Painting Guide: Easy to follow tip on how to paint veneer finish

Taking care of veneer is more difficult than installing it in the first place. Veneer can get really messy if you don’t have the correct idea of how to take care of it. Painting veneer is a good choice to make it look appealing, but the finish may not come out as desired if the surface isn’t prepared properly. Let’s then take a look at how to paint veneer to perfection.

Veneer can be really fragile, it can break easily and can build up with grim. Maintaining it can be a task, therefore it becomes mandatory to see that veneer surface is perfectly treated, cleaned and prepared before it is painted. Fortunately, preparing veneer is easy, it just requires repairing, sanding and a few coats of primer.
Before getting into painting the veneer surface, let’s take you through the process of preparing veneer for painting.

Things you’ll require:
Gloves
Wood glue
Warm water
Liquid dish soap
Sandpaper
Mask
Primer
Varnish
Paint (use oil-based paint or latex, do not mix oil paints with water, such pain doesn’t stick to the surface for long)
Paint brushes/roller

Repairing any cracks and damage, and cleaning it well

It’s easy to say – cracked veneer cannot be fixed. But all problems with veneer need to be fixed before painting. Small damages can be secured with wood glue, while cracked area can be replaced with new piece of veneer. After all the gluing, clean the surface with warm water to remove dust, grim and grease on the surface. If plain water doesn’t provide desirable results, you can use a few drops of dish soap in water. Do ensure that the crack and little damages you had repaired do not peel off. If you sense a problem, halt your cleaning process and fix the damage on priority.

How to paint veneer

Photo: www.doityourself.com

Sanding and Primer

If the veneer surface is in good condition, you can simple sand a little, prime it and paint, like you would on any other piece of furniture. However, if the veneer is chipped and damaged carry out the process above before sanding.

How to paint veneer ANEBODA chest – particleboard painted over

If the surface is not sanded, or isn’t sanded enough the paint will form bubbles or patches. Thus, after cleaning, lightly sand the veneer surface when it has completely dry. Sand it thorough to make the surface entirely even. Do not rub too hard. After sanding, remove all the dust on the surface to be painted using a dry cloth. Now, apply at least two coats of primer, allow the surface to dry between coats and after the two coats.

Veneer is a decorative wood layer that’s overlaid on a different surface. Veneer can be primed, painted , stained, and treated just like any other wood surface. The trick to painting veneer is to clean, sand, and prime it before applying a finish coat of paint .

Can you use furniture polish on wood veneer?

Wood veneer furniture is sensitive to water and can be seriously damaged by condensation. Be sure to thoroughly dry a veneer surface to prevent water damage. To repair small scratches on veneer furniture , simply apply oil polish to the area and massage with a soft microfiber cloth until the scratch fades away.

How can I paint over veneer without sanding?

Here are 5 Ways To Paint Furniture Without Sanding : USE A MINERAL PAINT . Mineral paint is very similar to chalk style paints in that no prep or prime is required. USE MILK PAINT + BONDING AGENT. As I already mentioned, the antique desk in this post was not prep- sanded . USE A BONDING PRIMER. USE A LIQUID SANDER /DEGLOSSER.

How can I tell if my furniture is laminate or veneer?

If you see the grain but the pattern tends to repeat and it lacks texture and feels perfectly smooth, it’s probably veneer . If it lacks grain altogether, it’s most likely laminate .

How can I tell if my furniture is veneer?

If there is a veneer , you will be able to look at it from the side and see where the sheet of veneer attaches to the front of the piece. Also, if you see unfinished wood underneath the furniture , it’s probably wood and not laminate – which tends to cover the furniture from top to bottom.

Can you whitewash veneer furniture?

If you want to create an opaque white finish, the best strategy is to apply a coat of wood primer followed by one or two coats of white paint. If you prefer a pickled look, mix flat latex paint or primer with an equal amount of water.

How do you refurbish veneer furniture?

Sand the veneered furniture with 120-grit sandpaper just enough to rough up the wood surface. Take care not to remove too much material as veneer is not too thick. Wipe the wood with a tack cloth and lightly sand again with 220-grit sandpaper to smooth the wood surface. Wipe it clean with a tack cloth.

Which polish is best for veneer furniture?

How do you polish veneer furniture?

Aim to dust your wood veneer regularly with a dry, soft cloth to help keep it looking its best. Then for a quick, non-deep clean , you can spray a wood veneer with a light layer of non-ammonia glass cleaner and wipe it with a paper towel. When cleaning , avoid using any furniture polishes that contain wax or silicone.

How do you care for veneer furniture?

Dust regularly with a slightly damp, soft, lint-free cloth. Wipe dry with a dry, soft cloth in the direction of the wood grain. Spills should be immediately wiped up with a damp cloth. Clean the surface with a soft cloth dampened with a quality cleaner formulated for wood furniture .

What happens if you don’t sand before painting?

When You Can Skip Sanding , Deglossing and Priming If the finish on your furniture isn’t damaged or chipping, it’s flat not shiny and you aren’t painting it a drastically different color, then you may be able to just go ahead and start painting . Before painting though, do make sure the piece is clean.

What kind of paint do you use on laminate furniture?

Latex paint is recommended for laminate surface painting projects because of its durability and smooth finish . Try ProClassic Interior Acrylic Latex Enamel for lighter colors, and All Surface Latex Enamel Base for deeper hues.

Can you paint over laminate furniture?

A: Like most rules, there’s always an exception, so YES, you can paint laminate furniture without sanding or priming IF you use the right kind of paint . You can skip the primer if you are painting laminate furniture with chalk paint .

If you are tired of living with outdated “wood” veneer paneling, paint over the paneled walls in your home. This requires preparation and attention to detail or your results will not be worth your effort. Spend the time to prepare your surface, and the finished result will be picture perfect. Preparation involves several steps, and will vary depending on your desired result, the original finish and the condition of the surface.

Things You’ll Need:

  • Tri-sodium phosphate (TSP) or liquid soap
  • Painter’s tape
  • Cleaning cloths or rags
  • Sanding block
  • Fine, medium and coarse sandpaper
  • Goggles
  • Facemask
  • Tack cloth
  • Paint tray
  • Primer (latex or oil based depending on your surface)
  • Paint brushes (bristle medium quality), foam brushes or paint pads
  • Small roller with fine texture refill
  • Acrylic latex paint
  • Drop cloth (commercial plastic or paper, or an old sheet)

Always work in a well-ventilated space. If you are working outside choose a clear day with no wind, as humidity and wind can ruin your finish. Use protective gloves, as it makes clean-up easier and protects your skin. Use a face mask and goggles when sanding to avoid inhaling the dust, particularly if you have varnished the surface. The varnish dust can severely irritate lung tissue. Use a drop cloth on the floor of your work space.

Warnings:

  • Dust is highly flammable. When sanding, make sure that there are no open flames around. If working in the basement, open any windows and turn off the pilot light on the water heater.

Preparation

Inspect and measure the surface area of your project to estimate supplies needed. If your surface has any stains, you will need to use a special primer designed for that purpose (BIN or Kilz). If your surface has an oil varnish, you will need an oil-based primer; otherwise use a latex one. (You can use latex paint after either primer.) Buy a little more paint and primer than you need. It is better to over-estimate, since you may need more than you think and touch-ups may be needed in the future.

Remove all switch plates, wall plates and anything else screwed to the wall. Tape all edges with painter’s tape to avoid “bleeding” onto adjacent surfaces.

Clean the surface using a dilute solution of TSP, or diluted liquid soap, and a clean rag. This will remove any grease and prepare the surface for sanding and priming. Do not make the surface too wet, since it must dry before sanding.

Repair the surface if it is pitted or has large holes. Glue down any raised veneer and fill holes with wood filler. To smooth out the surface, you can use drywall “mud” or caulking to fill in the grooves between panels. If the paneling is narrow or the surface has architectural details, then you may wish to leave it as is, since this is a labor-intensive step. (Consider making the grooves part of your paint design.)

Sand all surfaces. If you have used wood filler or caulking, you will first need to use coarse sandpaper to sand down the filler and make the surface completely level. Use medium sandpaper to scuff the rest of the surface so that the paint and primer will adhere properly. Sand all edges, including ones that you think may not be visible. Remove all dust from the surface with a tack cloth.

Priming and Painting

Paint a light coat of primer all over the surface using a small paint brush for edges and detail, and a roller or paint pad for larger surfaces. Priming is necessary to ensure that the new paint will “stick,” particularly if you have a shiny or varnished surface. Let it dry to the touch and then paint a second light coat. It is preferable to use two light coats rather than one heavy one, to avoid drips and sagging.

Sand lightly over the whole surface with fine sandpaper once the primer has dried completely. Remove all dust with a tack cloth.

Paint one light coat of good quality paint with a clean paintbrush and roller. Let it dry completely, then paint another coat. If your finish is not optimum, another light coat may be necessary. The choice of paint will partly determine this, so choose a paint with good “hiding” properties.

Replace all hardware once the paint has dried completely. Consider buying new switch plates to highlight your hard work. Clean your work area.

A veneered dresser that looks outdated may not be your favorite piece of furniture, but there’s no need to replace it if it’s still in good shape. Revamp that piece by giving it a makeover with paint, tailoring it to fit the room’s decor. Painting over wood veneer is just like painting over wood, except the wood layer is very thin, requiring care not to sand all the way through it. Any latex paint you like turns that outdated or ugly dresser into one that suits your tastes. You can also apply a stain over laminate, reports the Weathered Door, but painting is easier and faster.

If that veneer is actually a shiny piece of paper designed to look like wood grain, you need a special primer designed for slick laminate surfaces to ensure the primer adheres properly.

A coat of clear polyurethane over the dry paint helps protect the painted surface.

Give the dresser a distressed look by rubbing the painted surface with candle wax, applying a coat of paint in another color, then sanding through some of the top paint color with a sanding block in areas that would normally receive the most wear.

Color wash the dresser by applying a tinted glaze over the painted piece with a brush, then rubbing off most of the glaze with a rag.

Cover the floor of the work area with newspaper. Set the dresser atop the paper, ensuring the paper sticks out far enough beyond the dresser to catch any paint spills.

Sand the entire dresser surface, including the drawer fronts, with a fine-grit sanding block to scuff up the existing finish on the veneer, sanding with the wood grain. SAS Interiors recommends 120 grit. Scuffing the finish makes it more receptive to primer and paint. Wipe away the dust with a tack cloth or soft rag.

Cover any areas you don’t plan to paint with masking tape. Remove the drawers, if they come out completely, or pull them out several inches for better access to surrounding areas while priming and painting.

Pour some of the primer into a paint tray. Prime the entire dresser, including the drawer fronts, using a paintbrush, following the veneer grain. Let the primer dry completely. If the underlying finish is still visible beneath the primer, apply a second coat of primer, allowing it to dry.

Pour some of the latex paint into a paint tray. Paint the entire dresser with a paintbrush, following the grain of the veneer. Allow the paint to dry completely, then apply a second coat if the primer is still visible beneath the paint.

Click the link below and get directions to your closest Sherwin-Williams store.

How to paint veneer

Sign up for your PaintPerks ® benefits! It’s Free and Simple!

How to paint veneer

Color, Delivered.

How to paint veneer

No mess. No dry time.

  • Homeowners \ \ \
  • Paint a Laminate Dresser

Start by examining your piece of furniture to check for any old residue from its past life. Any leftover substances (like stickiness from tape, etc.) should scrape off easily with a paint stripper, if necessary – just be careful not to damage the surface.

Tip: Don’t forget to put a drop cloth down and work in a well-ventilated area.

Always start by washing the surface with a good cleaner degreaser. Use a sander to add a little texture to the surface and remove the laminate’s shine. This project used 150-grit sandpaper. Careful not to sand off the surface. Remove the dust from your surface with a dry cloth or dust spray.

Apply Sherwin-Williams Extreme Bond™ Bonding Primer with the mohair roller, and allow to dry. Once the primer has hardened, it’s time to lightly sand again. For this project, a 220-grit was used for this step. Remove dust.

Using a clean mohair roller, apply your first coat of paint. Wait 4 hours, then apply the second coat. See your paint can for specific drying instructions.

Latex paint is recommended for laminate surface painting projects because of its durability and smooth finish. Try ProClassic Interior Acrylic Latex Enamel for lighter colors, and All Surface Latex Enamel Base for deeper hues.

Clean up:

Always clean your brushes for future use. Learn how to properly store and dispose of paint here.

  • Browse Project Center
  • Previous ←
  • Next →

Project Overview

Don’t look past laminate just because you aren’t crazy about its color. Painting laminate is simple, as long as you have the right products for the job. Project and images from Mandi at Vintage Revivals.

Supplies For This Project

  • All Surface Enamel Latex
  • Contractor Series Mohair Mini Roller
  • Hand sander
  • Contractor Series Canvas Drop Cloth 12oz
  • Extreme Bond Bonding Primer
  • 150-Grit Sandpaper

Colors We Used

How to paint veneer

Choose Color with Confidence

*WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

Prime your laminate cabinets for the perfect paint job with these tips for surface preparation, paint selection, and application.

How to paint veneer

Short of committing to a more costly replacement of outdated kitchen storage, repainting laminate cabinets is an affordable way to turn the eyesore into eye-catching, modern cabinetry. But while you may be well-versed in painting most any old wood furnishings, from side tables to pantry doors, laminate is another beast altogether. Not nearly as porous as its wooden lookalike, this type of surface requires unique preparation, paint, and paint application. Follow these best practices to reinvigorate your laminate cabinetry with a fresh face that lasts!

DON’T PAINT OVER DAMAGED LAMINATE

If laminate is cracked, warped, or peeling, that damage can interfere with the bonding of paint to the cabinet. Ensure that the laminate is in good condition by repairing minor laminate damage or re-facing cabinets before applying paint.

DO REMOVE CABINET HARDWARE

Remove knobs, pulls, and other visible cabinet hardware before painting laminate cabinets for smooth paint application without obstructions. You can mask metal on the hinges with painter’s tape and paint the doors in place, or, if the hinges are visible and removable, take the doors down from the cabinets and paint them separately on a work bench or sawhorse.

How to paint veneer

Photo: Zillow Digs home in New York, NY

DON’T LEAVE DIRT AND GRIT BEHIND

It may be tempting to eyeball your cabinets and decide that any dirt is minimal enough to conceal with a paint job, but your dirty secret will get out when the color fails to adhere well to the laminate. Before you start painting laminate cabinets, gently wipe away settled-on grime and grease using trisodium phosphate. Then, rinse with fresh water and dry the cabinets completely.

DO SAND THE CABINETS

To create a strong bond between the paint and your cabinet, you’ll need to roughen up the slick laminate with the help of a gritty companion: sandpaper. (For better coverage of a large surface area, consider upgrading to a motorized orbital sander. Your upper body will thank you.) Thoroughly scuff the surfaces of the cabinet with 120-grit sandpaper—enough to get a dusting, but not so much that you tear through the paper-thin laminate surface—and clean up any dusty remains with a handheld vacuum and a damp cloth.

DON’T USE ANY OLD PRIMER AND PAINT

Laminate doesn’t play well with all primers and paints, only those specially formulated to adhere to its picky surface. If you opt for a primer, choose a bonding primer tenacious enough to stick to laminate (view example on Amazon), and then top it with an oil- or latex-based paint after the primer has cured. If you select a paint that can be applied directly over laminate (view example on Amazon), you can skip the primer—just know that this qualification may limit your color choice.

How to paint veneer

Photo: Zillow Digs home in Altanta, GA

DO PUT YOUR PAINT TO THE TEST

Paint in hand, you’re almost ready to get to work. But first, double-check that your stock is well suited for the job. Testing its bonding capabilities before diving into an entire paint job could save you from a case of peeling paint down the road—and the need to redo hours of work. Apply your paint to a small, inconspicuous area of the cabinet (like the back of one you hardly ever open), let it cure, then inspect the bonding. If you spot some bubbles in the coat, that means it is not adhering well; consult a paint dealer at your hardware store to pinpoint a more suitable paint for the job.

DON’T LEAVE BRUSH STROKES BEHIND

If your first-choice paint applicator for the traditionally flat surface of laminate cabinets is a brush, take a moment to reconsider. These popular paint tools tend to leave an unsightly trail of brush strokes in their wake. Opt instead for a roller, sprayer, or a paint pad for a streak-free finish.

DO MINIMIZE YOUR EXPOSURE TO FUMES

Due to the powerful fumes released from the primer and paint (and your close proximity to them when painting laminate cabinets), increase ventilation in the room and keep out children and pets. Lastly, pull on a pair of chemical-resistant work gloves before you go off to paint the town—or perhaps in this case, your cabinets—red!